U-Line U-1075WC Guía para resolver problemas descargar pdf (Pagina 12)

12 1075WC

Light Bulb Replacement

To replace the light bulb in your U-Line unit:

Figure 14

1. Grasp the edges of the light housing lens opposite the

exposed tab and gently push the lens toward the tab

(Figure 14, ).

2. Pull the edge of the lens down and swing it out of the

light housing.

IMPORTANTIMPORTANT

ALWAYS use a genuine U-Line replacement bulb (P/N

31317) in the light housing. Use of any other bulb

within the housing will generate excessive heat,

causing damage to the light housing and cabinet

interior, and will compromise the precise

temperature control of your unit.

3. Replace the bulb only with a genuine U-Line P/N 31317

replacement.

4. Replace the lens by first inserting the tab side back into

the housing at a slight angle. While gently pushing the

lens towards the tab end, push the free end up into the

housing, and release when you will hear a snap/click.

Wine Rack Removal/Installation

To remove a rack from the cabinet:

1. Grasp the end of the rack, and gently slide it out until

it stops.

2. Remove any bottles stored on the rack.

3. Press the left rack release lever

(Figure 15)

down, and

at the same time, lift the corresponding right rack

release lever up, and pull the rack out until it is free of

the tracks and the cabinet.

Figure 15

IMPORTANTIMPORTANT

Do not remove the track side rails from the cabinet.

To insert a rack in the cabinet:

1. Align the left and right rack channels with the tracks

in the cabinet, and ensuring an even track

engagement on both sides, gently push the rack into

the cabinet until it stops.

2. Before reloading the rack, ensure proper operation of

the travel stops in the left and right track rails by

pulling the rack out gently until it completely stops.

Wood Trim Finishing

Interior components of your U-Line unit are equipped

with a natural wood trim for appearance and durability.

Although this wood trim has been coated with a clear

sealer at the factory, it is recommended that the trim be

stained (if desired), and receive a final finish coating prior

to the unit going into full-time service.

WARNING

To prevent permanent damage to the inner liner

of your unit, the wood trim MUST be removed

from the unit for staining and/or finishing. Allow

stain/finish to dry thoroughly (at least 24 hours

per coat) in accordance with the product

manufacturer’s instructions prior to

reinstallation. Failure to do so may cause the

inner liner of the unit to have a permanent odor,

which is not covered by the warranty.

If staining the trim is desired, it must be done before the

application of any type of final finish. Review the

following staining/final finish and final finish-only

guidelines when staining/ and or sealing the wood to

ensure proper adhesion and durability of the finish.

NOTE: Glass in door is tinted. Stain may look darker when

door is closed.

Staining and Final Finish Application

1. Remove all screws securing wood trim to interior

components, and remove the trim from the cabinet

interior.

NOTE: Your model may contain an electronic display

panel in the lowest level trim piece. After removing the

trim screws, and gently pulling the trim from its location,

a wiring harness connector will become visible. Unplug

the connector, and remove the trim from the interior.

IMPORTANTIMPORTANT

DO NOT use oil-based stains on wood trim. Vapors

from oil-based stains will permanently penetrate

the liner and will not dissipate over time.

2. Apply Minwax

Water-Based Wood Stain to wood with

a synthetic bristle brush or a foam applicator. Allow

ULIN_0001_A

ULIN 0162 A

1 2 ... 7 8 9 10 11 12 13 14 15 16

Comentarios a estos manuales

Sin comentarios

U-Line U-1075WC Guía para resolver problemas Pagina 12

Comentarios a estos manuales

Relacionado con productos y manuales para No U-Line U-1075WC