U-Line CLR2160 Guía de instalación

www.U-LineService.comPhone (414) 354-0300 • FAX (414) 354-7905Service & Parts Tech Lines Phone (800) 779-2547 • FAX (414) 354-5696OnlineService@U-

www.U-LineService.com 10 05/2007CLR2160/CLRCO2175 Ice Makers2. Pull door gasket out of groove (top edge of door only). Start in the middle and pull ou

05/2007 11 www.U-LineService.comCLR2160/CLRCO2175 Ice Makers2. Create a relief (Figure 19) for pivot plate by cutting notch in top corner of overlay p

www.U-LineService.com 12 05/2007CLR2160/CLRCO2175 Ice Makers 3. Attach the door panel to the overlay panel using #10 x 5/8" wood screws and nylon

05/2007 13 www.U-LineService.comCLR2160/CLRCO2175 Ice Makers4. Attach Top Pivot Plate to door handle, on side where hinges will be. Use the two #8-32

www.U-LineService.com 14 05/2007CLR2160/CLRCO2175 Ice MakersChecking Door AlignmentThe unit’s door is aligned at the factory before shipment. However,

05/2007 15 www.U-LineService.comCLR2160/CLRCO2175 Ice MakersCAUTIONPlumbing installation must observe all state and local codes. All water and drain c

www.U-LineService.com 16 05/2007CLR2160/CLRCO2175 Ice Makers• Drain line does not create traps or created traps are vented (see Figure 37).See Figure

05/2007 17 www.U-LineService.comCLR2160/CLRCO2175 Ice Makers2. Carefully push the power cord grommet through the hole in the back panel (see Figure 40

www.U-LineService.com 18 05/2007CLR2160/CLRCO2175 Ice MakersWARNINGTo prevent accidental electrocution, make certain that the floor surfaces surroundi

05/2007 19 www.U-LineService.comCLR2160/CLRCO2175 Ice Makers3. Attach the copper water line to the back of the unit using the supplied clamp and the b

www.U-LineService.com 2 05/2007CLR2160/CLRCO2175 Ice MakersContentsExterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Cu

www.U-LineService.com 20 05/2007CLR2160/CLRCO2175 Ice MakersElectrical SpecificationsCAUTIONElectrical installation must observe all state and local c

05/2007 21 www.U-LineService.comCLR2160/CLRCO2175 Ice Makers2. If the ice maker is not level, adjust the feet on the corners of the unit as necessary

www.U-LineService.com 22 05/2007CLR2160/CLRCO2175 Ice MakersRelocating the Shelves (CLRCO2175)Both the glass shelves in the refrigerator and the inner

05/2007 23 www.U-LineService.comCLR2160/CLRCO2175 Ice MakersInitial Start-UpOnce installation and leveling is complete, the unit is ready for initial

©2007 U-Line CorporationPublication No. 30141E05/2007 Rev. DU-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-i

05/2007 3 www.U-LineService.comCLR2160/CLRCO2175 Ice MakersGeneral PrecautionsUse this appliance for its intended purpose only and follow these genera

www.U-LineService.com 4 05/2007CLR2160/CLRCO2175 Ice MakersInspectionUnwrap and inspect the unit on a flat, level surface capable of supporting its en

05/2007 5 www.U-LineService.comCLR2160/CLRCO2175 Ice MakersYour U-Line product has been designed for either free-standing or built-in installation. Wh

www.U-LineService.com 6 05/2007CLR2160/CLRCO2175 Ice MakersCut-Out Dimensions CLRCO2175Follow the cut-out drawing in Figure 4. The 24-3/16" width

05/2007 7 www.U-LineService.comCLR2160/CLRCO2175 Ice MakersReversing the Door(Black and White Units Only)All U-Line units (except Stainless Steel mode

www.U-LineService.com 8 05/2007CLR2160/CLRCO2175 Ice MakersOther Site RequirementsPower SupplyThe unit requires a grounded and polarized 115 VAC, 60 H

05/2007 9 www.U-LineService.comCLR2160/CLRCO2175 Ice MakersSide-By-Side Installation Instructions CLRCO2175For a complete refreshment center, install